Here we are assuming the Config Mgr server is 10.0.0.10/24, and clients are on 10.0.1.0/24 (VLAN 10) and 10.0.2.0/24 (VLAN 20) First thing we need to do is on the core switch (the 5406). for 10.0.1.0/24 the subnet's broadcast is 10.0.1.255). WOL - Magic Packet Sender to stosunkowo lekkie oprogramowanie, które nie zajmuje tyle miejsca, co przecitny program w kategorii Oprogramowanie sieciowe. This means sending to the subnet's broadcast address instead (e.g. Broadcasts sent to 255.255.255.255 don't traverse routers into other subnets so we instead have to use a subnet directed broadcast. It's a UDP packet usually going from port 7 to port 9. Wake on LAN works by broadcasting a magic packet containing the MAC of the PC you want to wake. I've since written a new post about Wake on LAN, which may be useful for troubleshooting. To send WoL packets while testing I'm using a tool from (once all set up Config Mgr will be doing the wake on LAN packets). I'm using mostly HP v1910/1920 edge switches with a HP 5406zl core switch. Click OK.Īfter the above configuration, you can now launch a third-party WOL software on PC B and send a Magic Packet to boot up PC A.By Katy Nicholson, posted on 10 June, 2018Īs part of setting up Config Mgr I wanted to get all PCs to wake-on-LAN to enable truly zero touch deployment. Specify the internal server IP as 192.168.0.100, which is the IP address of PC A. Specify the external port and internal port as 7, which is used to receive Magic Packets. Specify the WAN port according to the network environment. W ake-on-LAN (WOL) is an Ethernet networking standard that allows a server to be turned on by a network message. Click OK.Ĭhoose the menu Transmission > NAT > Virtual Servers and click to load the following page. Enter the IP address and MAC address of PC A. If there is not a desired entry, click to load the following page. Look at the results and make note of the port. Type 'ping' followed by the computer that you will be sending the wake-on-LAN commands IP address. Check if the desired IP address is reserved for PC A. Open the Command Prompt on the computer from which you will be sending the wake-on-LAN command. Programowanie Sieci Windows Licencja: Wszystkie Cisco Packet Tracer 8.1. Click OK.Ĭhoose the menu Network > LAN > Address Reservation to load the following page. WOL - Magic Packet Sender to pomocne, bezpatne oprogramowanie Windows, nalece do kategorii Sieci oprogramowanie. Enable Export to DHCP Address Reservation. In the IP-MAC Binding List section, click to load the following page. In the Scanning Result section, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > IP-MAC Binding to load the following page. Wait a minute until the scanning is completed. In the general section, specify the scanning IP range according to the DHCP address pool. If the desired entry is in the list, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP Scanning to load the following page. There are three methods to do IP-MAC binding: bind in the ARP list, bind in ARP scanning result, or add IP-MAC Binding list entry manually.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP List to load the following page. To achieve this requirement, you can configure the router as follows:Īfter you complete the configuration, you can use a WOL software to wake up PC A on PC B.įollow the steps below to configure the router. Make sure the WAN port of the router is routable from PC B.PC A should be powered off normally and the power supply is normal.In network card properties configuration of PC A, allow the network card to wake up the PC, forbid the PC to turn off the network card to save power, and enable Wake on Magic Packet. Make sure that the network card of PC A supports WOL.In BIOS setup of PC A, enable Power On By PCIE or Wake Up On LAN. Make sure that the motherboard of PC A supports WOL.It is required that PC B can wake up PC A by sending a Magic Packet via the internet.īefore configuring WOL, you should do the following preparation: In the diagram below, PC A is connected to the internet via the router. You can check WOL Magic Packet Sender, SmartRF Packet Sniffer, Colasoft Packet Player and other related programs like Engage Packet builder at the 'download' section. The product will soon be reviewed by our informers. You can use WOL (Wake on LAN) to boot up your PC from a remote place by sending a Magic Packet via the internet. The name of the program executable file is PacketStream.exe.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |